- LED DISPLAY COOLTERM WITHOUT BEING CONNECTED SERIAL
- LED DISPLAY COOLTERM WITHOUT BEING CONNECTED VERIFICATION
- LED DISPLAY COOLTERM WITHOUT BEING CONNECTED SOFTWARE
- LED DISPLAY COOLTERM WITHOUT BEING CONNECTED CODE
The host bootloader window shows that it finished the downloady successfully, but the LED remains blinking at the fast rate and entering commands such as a question mark on the Coolterm/TeraTerm window would only show a checkmark. Then when you complete the download, the application program should start automatically (the LED will flash at a slower rate) and if you enter a question mark on the Coolterm window, you should again see a list of commands. After you enter UPG, the "Jumping to Bootloader" message is displayed and the application program is exited and the bootloader entered (I agree, BootLoadable_Load() does not return). So before you type UPG, enter a question mark, a small list of commands will be displayed. The list of commands will only be displayed if you enter a question mark in the Coolterm window when the application is running. cyacd file of some other project other than DevBoard_LHSApp.cydsn project.Then please provide that.įrom my observation after step#4 mentioned,the device is executing the application code. Please explain why after programming second time the same.cyacd file, on Coolterm or TeraTerm you expect a display of list of commands automatically on Enter.Īre you programming second time with some other. cyacd file of DevBoard_LHSApp.cydsn project.Again,the port P2_1 LED(connected to ActivityLED signal) started blinking with the ON time as decided by the ledCtr variable value which shows that it again started to execute the application. cyacd file.The port P2_1 LED(connected to ActivityLED signal) started blinking with the ON time as decided by the ledCtr variable valueģ)Opened the Coolterm,connected the COM port and given the command UPG(snapshot attached).Device entered into the bootloader modeĤ)Disconnected the COM port from Coolterm,and opened the Bootloader host utility and again programmed the. I followed certain steps to recreate your issue-ġ)First programmed the kit with the bootloader project(DevBoard_Bootloader.cydsn),thus the Pin_LED which is connected to P2_1,blinked with ON time of 127ms as expected.Ģ)Then ,I builded the Bootloadable project(DevBoard_LHSApp.cydsn),programmed using the Bootloader Host the.
LED DISPLAY COOLTERM WITHOUT BEING CONNECTED SOFTWARE
"This method will never return" means that whatever you have return in the application after the execution of "Bootloadable_Load()"API will never get executed because it will cause a software reset everytime the API gets executed It will load a new application and reset the device. Schedules the Bootloader/Launcher to be launched and then performs a software reset to launch it. In the bootloadable component datasheet page# 16 it is stated that. Thanks very much for your help, I really appreciate it!
LED DISPLAY COOLTERM WITHOUT BEING CONNECTED VERIFICATION
When the bootloader runs, it should then fail its application verification and wait for new code. Is there another way to achieve my goal of having the application jump to the bootloader? I guess I could trash its checksum in flash, then just do a reset. It appears that using the Bootloadable_Load command does something to prohibit the application from executing automatically. I repeated this test multiple times, each with the same results.
LED DISPLAY COOLTERM WITHOUT BEING CONNECTED CODE
I then closed TeraTerm and used the Host Bootloader utility to download the code (without entering the UPG command, which again indicates that the application was not executed), it will complete and this time, it will automatically execute the application. After I close the port (also tried exiting the utility), then opened TeraTerm and entered a question mark, TeraTerm displayed a "check mark" character. Enter ? - Which should display a list of commands.Īfter I jump from my application to the Bootloader (via Bootloadable_Load) and download the new firmware vis the Host Bootload utility, the application program is not automatically executed. Select another port in the Host Bootloader utility to close the current one.ĩ. Launch TeraTerm to talk to the application.ħ.
This is done using the command, " Bootloadable_Load()".ġ. One of the commands, "UPG" is used to jump to the bootloader and begin the download process.
LED DISPLAY COOLTERM WITHOUT BEING CONNECTED SERIAL
As you can see, the application accepts commands over the serial port (which is also used by the bootloader to get the new firmware code). The application started running as expected. I rebuilt the bootloader and application and downloaded both via the IDE. To print information to the Arduino IDE Serial Monitor.I downloaded PSoC Creator 4.0. Serial object on standard Arduino boards. Teensyduino provides a Serial object which is compatible with the
0 kommentar(er)
